FAQ

 Barcode Reader Connection

A barcode reader can be connected to either the USB port or the COM1 port on the GP3000 series.
For the details, please refer to GP-Pro EX Reference Manual 16.2 Connecting a Barcode/Two-dimensional Code Reader.

NOTE
* Each of the COM1 port and the USB port allows one barcode reader to be connected to, however, if you connect two barcode readers at the same time and store the code data in the Data Display part or the internal device from both barcode readers, the system may not work properly. One barcode reader should be set up to store data to the Data Display part, and the other should be set up to store data to the internal device.

Connecting a barcode reader to the USB port
*
Connection Structure
Connect a barcode reader to the USB port on the GP3000 series.
*
Tested barcode readers
Manufacturer
Model
Type
Supported models
Supported version
GP3000 Series
(except
GP3200 Series)
GP3200 Series
TOHKEN CO., LTD.
THLS-7000ESD-USB
Barcode reader
2.00.000
THLS-6920USB
Barcode reader
2.00.000
THLS-6800USB
Barcode reader
2.00.000
THLS-6910
Barcode reader
-
1.00.002
THLS-1900
Barcode reader
-
1.01.004
*2
HAND HELD PRODUCTS, INC.
IT-5800
Barcode reader
-
1.01.004
*2
DENSO CORPORATION
GT10B-SU
Barcode reader
-
1.01.004
*2
GT10B-SB
Barcode reader
-
1.01.004
*2
KEYENCE CORPORATION
BL-210UB
Barcode reader
-
1.10.000
BL-N70UB
Barcode reader
2.00.000
BL-N60UB
Barcode reader
-
1.01.001
*3
Symbol Technologies, Inc.
LS3408FZ
Barcode reader
-
1.01.004
*2
LS9208
Barcode reader
-
1.01.004
*2
IDEC DATALOGIC
CO., LTD.
HERON-D130
Barcode reader
-
1.01.004
*2
Opto Electronics Co., Ltd.
OPL-6845-USB *1
Barcode reader
-
1.10.000

NOTE
*1 The OPL-6845-USB software version FM22J03 or higher is required. (The system may not operate properly if the firmware version of the barcode reader is lower than the above mentioned.) Please refer to the instruction manual attached to the barcode reader.
*2 The system may not operate properly with GP-Pro EX V.1.01.004 or lower.
*3 The system may not operate properly with GP-Pro EX V.1.01.001 or lower.


Connecting a barcode reader to the COM1 port
*
Connection Structure
Connect a barcode reader to the COM1 port on the GP3000 series.


IMPORTANT
*
Use the RS-232C cable and the power supply provided with the barcode reader. (The 5V power supply of COM1 on the AGP is not available.)

*
Tested barcode readers
Manufacturer
Model
Type
Supported models
Supported version
GP3000 Series
(except
GP3200 Series)
GP3200 Series
TOHKEN CO., LTD.
TLMS-3500RV
(RS-232C)
Barcode reader
2.00.000
THLS-6800
(RS-232C)
Barcode reader
-
1.00.002
THLR-3000N
2D code reader
-
1.00.002
Nichiei Intec Co., Ltd.
FFTA10A
Barcode reader
-
1.00.002
AIMEX Corporation
BW-880RS-B1
Barcode reader
-
1.00.005
DENSO CORPORATION
QS20H-I-R
2D code reader
-
1.00.003
*4

NOTE
*4 When you set "DENSO Mode", some of the codes may not be read.


Contact Us | Tech Support | Customer Care | Repairs | Privacy Policy | Terms of Use | Prop 65
Copyright (c) 1996-2019 Schneider Electric Japan Holdings Ltd. All Rights Reserved.