Set the format for printing sampling data from a printer
connected to the display unit.
The following is a settings guide for [Basic]. Refer to the
following for Custom Settings.
Print
Select whether or not to print. When printing sampling data,
ensure that this option is checked, and select the print
format.
25.11.5 Printing
Basic Settings/Custom Settings
Select the print format setting mode.
Use a preset format to easily configure
settings.
Set a customized format.
Print Mode
Select the print timing.
Printing is performed every time sampling
occurs.
Data is printed in block units. This can only
be set when in the [Mode] tab's Extended area the [Overwrite old
data after finishing the specified cycles] check box is
cleared.
Printing is started via the [Print Control Word Address].
Print Control Word Address
When the [Print Mode] is set to [Batch], select an address to
control the start of printing. When 0 bit of the designated address
turns ON the printing starts.
Two sequential Words are used to store the Word Address: the
control Word and the block number. Select the block number and
start the printing.
Print Completion Bit Address
When the [Print Mode] is set to [Batch], select an address to
confirm the completion of the printing.
Designates the Bit Address to be turned ON when data is printed
out for each block. After confirming that this Bit Address is
turned ON, perform the next printing.
Date
Defines whether or not to print the date, as: [yy/mm/dd],
[mm/dd/yy], [dd/mm/yy], or [mm/dd]. "yy" prints the last two digits
of the year, and "mm" and "dd" use two digits to print the month
and date."yy" displays the last two digits of the year, and "mm"
and "dd" use two digits to display the month and date.
Time
Select the time format [hh:mm], [hh:mm:ss] or [hh:mm:ss.ms].
"hh" displays the hours, "mm" displays the minutes, and "ss"
displays the seconds, all using two digits. "ms" uses three digits
to display the milliseconds.
Number of Characters
If in the [Mode] tab's Extended area the [Overwrite old data
after finishing the specified cycles] check box is selected, set
the number of characters to display in a cell.
Item Name (Horizontal) Characters
If in the [Mode] tab's Extended area the [Overwrite old data
after finishing the specified cycles] check box is cleared,
designate whether or not to print the Item Name row. If printing,
the number of characters in the block name can be from 1 to 20
(single-byte).
For the Date and Time columns, the item names will be printed as
[Date] and [Time]. For a Data column, the address will be
printed.
Item Name (Vertical) Characters
Select whether or not the Item Name column will be printed.
Data Display
Click [Data Type Settings] to open the [Data Settings] dialog
box. The data type, input range, number of display digits can now
be set.
25.8.6.1 Print/Data
Settings - Data Type
Total
If in the [Mode] tab's Extended area the [Overwrite old data
after finishing the specified cycles] check box is cleared,
designate whether or not to print the Total row. Click on [Data
Type Settings] and open the [Calculation Settings] dialog box. The
number of display digits for the Totals rows can now be set.
25.8.6.3
Print/Calculation Settings - Data Type
Ruled Line
Select whether or not the ruled line will be printed.
Preview
Opens a preview screen to confirm the print image.
Preview area
Displays the set contents with the selected print format.
If in the [Mode] tab's Extended area the [Overwrite old data
after finishing the specified cycles] check box is selected, only
one data row will be displayed. If the [Overwrite old data after
finishing the specified cycles] check box is cleared, the data rows
equal the designated [Occurrences].
When [Overwrite old data after finishing the specified cycles]
check box is selected
When [Overwrite old data after finishing the specified cycles]
check box is cleared
